Short answer: Cleanse your face, apply an even layer of Nebulyft Botanical Gel, switch the device on at a comfortable level and glide it slowly over your skin for the 10-minute session. Massage in or wipe off what is left of the gel when you finish. Nebulyft recommends one session a day, then three a week once you are happy with your results.
Key takeaways
- A session lasts 10 minutes. Consistency matters more than intensity.
- Always use enough conductive gel and keep the device moving.
- Start on the lowest level and do a patch test before your first full session.
- Many users start to notice results after about four weeks of regular use.
- Do not use the device if you have a pacemaker or another active implant, or if any other contraindication below applies to you.
Before your first session
- Read the manual that came with your device. It is the final word on settings and safety for your model.
- Charge the device fully. The R2 charges wirelessly and runs 4 to 5 ten-minute sessions on one charge. For the R1, follow our R1 charging guide.
- Check that RF is right for you. Read the safety section at the end of this guide before you start.
- Do a patch test. Try the lowest level on a small area of your jawline and wait a day to see how your skin responds.
What you need
- Your Nebulyft R1 or R2
- Nebulyft Botanical Gel, made for Nebulyft devices
- A gentle cleanser and a soft towel
- Optional: a facial water mist, in case the gel starts to dry
How to use the Nebulyft R1 and R2, step by step
- Cleanse and dry your face. Remove makeup and sunscreen so the device can make even contact with your skin.
- Apply the gel to one area at a time. Spread an even layer over the area you are about to treat, such as your forehead, one cheek or your jawline, so the gel does not dry before you reach it.
- Switch on and choose a level. On the R2, start on the lowest of its five energy levels and only move up if it stays comfortable. On the R1, use the buttons and LED indicators as shown in your manual.
- Place the treatment head flat on your skin. Keep the whole surface in contact with the gel. Gentle warmth is normal. Both devices hold a set operating temperature of 107.6°F (42°C) while they monitor heat.
- Glide slowly and keep moving. Work in slow, gentle strokes and never hold the device still in one spot. Move on to the next area once you have covered the first one.
- Top up as you go. If the device starts to drag, add a little more gel. If the gel dries too fast, lightly mist your face with water.
- Finish the 10-minute session. Massage the remaining gel into your skin or wipe it away, then follow with your usual moisturizer. A hyaluronic acid sheet mask is a calm way to finish.
How often should you use your device?
Nebulyft recommends one 10-minute session a day. Once you have reached the results you want, you can drop to three sessions a week to maintain them. Many users start to see changes after about four weeks of regular use. Some notice a fresh glow or less puffiness straight after a session, but lasting changes take time, so judge your progress over weeks, not days.
R1 and R2 at a glance
| Nebulyft R1 | Nebulyft R2 | |
|---|---|---|
| Technology | Multipolar RF | Multipolar RF with Microdot 2.0: 320 gold microdots on a large panel |
| Treatment head | Panel of 2.79 sq in (18 sq cm) | Large microdot panel |
| Temperature | Set at 107.6°F (42°C), with monitoring | Set at 107.6°F (42°C), with 4-channel monitoring |
| Controls | Mechanical buttons and LED indicators | Five energy levels, plus Nebulyft app integration |
| Charging | See the R1 charging guide | Wireless charging, 4 to 5 sessions per charge |
| Session | 10 minutes | 10 minutes |
Cleaning and care
- Wipe the treatment head with a soft, damp cloth after every session so no gel dries on it.
- Nebulyft devices resist splashes, but never submerge them in water.
- Store the device somewhere dry, away from heat and direct sunlight.
- Use only Nebulyft gel. Other products can change how the device makes contact with your skin.
Troubleshooting
- The gel dries too quickly: mist your face lightly with water before you apply the gel, and work on smaller areas.
- It feels too hot: keep the device moving, add more gel, or drop to a lower level. Stop if the heat feels uncomfortable.
- The device drags or skips: add more gel so the whole head stays in contact with your skin.
- The device switches off early: charge it fully and try again. If it keeps happening, contact support@nebulyft.com.
Safety: who should not use Nebulyft
Do not use a Nebulyft device if you:
- Have a pacemaker, internal defibrillator or any other active electrical implant
- Have permanent implants in the treatment area, such as metal plates, screws, silicone implants or dental implants
- Have or have had cancer, or are being treated for it
- Have had chemotherapy or electrotherapy in the past three months
- Have a severe endocrine disorder, such as diabetes or thyroid disease
- Have epilepsy
- Have sores, psoriasis, eczema, a rash or another skin condition in the treatment area
- Have had surgery in the past three months
If you are pregnant or breastfeeding, have recurring cold sores in the treatment area, or have seen a dermatologist about a skin condition in the past six months, talk to your doctor first. Before you treat the front of your neck, read our guide to the thyroid area.
Frequently asked questions
Can I use my Nebulyft every day?
Yes. Nebulyft recommends one 10-minute session a day, then three sessions a week for maintenance once you are happy with your results.
How long until I see results?
Many users notice changes after about four weeks of regular use. Results vary with your skin and how consistently you use the device.
Can I use Nebulyft if I have Botox or fillers?
Nebulyft can be used alongside treatments like Botox and fillers, but check with the provider who treated you first so they can advise you on timing.
Can I use a different gel?
Nebulyft Botanical Gel is made for Nebulyft devices, so it is the one we recommend. Our conductive gel guide explains why serums and oils are not a good substitute.
Is the device waterproof?
Nebulyft devices are built to resist water splashes and dust, but they are not made to be submerged. Wipe them clean instead of rinsing them under running water.
Related guides
- Nebulyft before and after: real results, timeline and what to expect
- Nebulyft N1 charging and usage guide
- Radiofrequency and microcurrent skin tightening: how it works
- How to choose the best at-home radio frequency device
This guide is for general information. Always follow the manual that came with your device, and talk to your doctor if you are unsure whether RF treatment is right for you.
